What are the four left-turning tendencies of an aircraft? Four Effects Behind the Leftward Pull The four (4) left-turning tendencies are torque, P-factor, spiraling slipstream, and gyroscopic precession. This article applies to most Single-Engine Piston aircraft, where the propeller rotates clockwise when viewed from the flight deck. Torque reaction: The engine turns the propeller one way, and the airplane reacts in the opposite direction. In flight, this tends to roll the airplane left. On the ground, extra load and drag on the left main wheel can also help turn it left. P-factor: At a high angle of attack, the descending propeller blade on the right takes a larger bite of air than the ascending blade. Its greater thrust pulls the nose left. This becomes more noticeable with high power and a nose-high attitude. Spiraling slipstream: Propeller wash curls around the fuselage and strikes the left side of the vertical tail. That side force yaws the nose left, especially with high propeller speed and low forward speed. Gyroscopic precession: A spinning propeller behaves like a gyroscope. When its plane of rotation is tilted, the resulting force acts about 90° later in the direction of rotation. Raising the tail of a tailwheel airplane during takeoff can therefore create a left yaw. The effect depends on the aircraft and the pitch change; it is not a constant left pull in every airplane. What to Notice in Green Castle Airplanes On a departure in the Club's Cessna 172E N7717U, increasing power while the airplane is still slow is a good time to anticipate left yaw. Keep your eyes outside and use the rudder needed to maintain directional control during the roll. After liftoff, adjust rudder pressure to keep the climb coordinated as airspeed and power change. The Club's Aeronca 11AC Chief N9576E gives the fourth item a more tangible setting: it is a tailwheel airplane, so raising the tail changes the spinning propeller's plane. The FAA identifies that pitch change as the classic situation in which gyroscopic precession becomes more noticeable. The exact control pressures still belong to the airplane and conditions at hand. If you want a related departure-safety example at IA24, the Club's takeoff decision-making scenario shows why noticing what the airplane actually does matters more than assuming every takeoff will feel the same. These tendencies help explain the need for active directional control. Wind, alignment, and aircraft handling matter too; a left drift on the runway is not automatically proof of any single propeller effect. FAA Sources and References FAA Pilot's Handbook of Aeronautical Knowledge, FAA-H-8083-25C, Chapter 5, “Torque and P-Factor,” pp. 5-30–5-33 Next Week Systems - Airspeeds Define these V speeds not shown on the airspeed indicator: Vₐ, Vₗₒ, Vₗₑ, Vₓ, and Vᵧ. Some important operating and climb speeds do not appear as colored marks on the dial. Next week, we will sort out what each one describes and why the current aircraft's approved information matters more than memorizing a speed from another airplane.
0 Comments
What are airworthiness directives (ADs), and when are they issued?When the FAA Requires Corrective Action An Airworthiness Directive, or AD, is a legally enforceable FAA rule used to correct an unsafe condition in an aircraft product. Under 14 CFR § 39.3, a product may be an aircraft, aircraft engine, propeller, or appliance. The FAA issues an AD when both findings in § 39.5 are met:
The AD itself identifies the affected product and states what must be done and when. Depending on the unsafe condition, it may require an inspection, repair, replacement, modification, operating limitation, or recurring action. The exact applicability, required action, and compliance time in the AD control; a familiar model name or a maintenance-shop summary is not enough. Applicability also extends beyond the airframe. An airplane can have separate ADs for its engine, propeller, and installed appliances. The FAA therefore directs owners and operators to search each product and to check the precise model, series, part number, serial number, and modification details stated in the AD. Checking AD Status for a Club Airplane The owner or operator is primarily responsible for keeping an aircraft airworthy, including compliance with Part 39. No person may operate a product that does not meet an applicable AD. Maintenance records must show the current status of applicable ADs, the method of compliance, the AD number and revision date, and the next required time and date when an action recurs. For practical review, ask four questions:
At Green Castle, CrewChief Systems provides Club members access to aircraft status, squawks, and airworthiness and maintenance records. For N84455, members can review the active AD and service-bulletin list, open the AD Compliance Report from Aircraft Logs, and view the full report last completed by a certificated mechanic. The related training blog post on required aircraft inspections explains where AD status fits beside inspection currency, while another post explains why effective registration and airworthiness certificates alone do not prove the airplane is airworthy today. The pilot does not need to memorize every AD. However, they should know where current status is recorded, recognize when something is unresolved, and stop before flight until the proper maintenance answer is clear. FAA Sources and References
14 CFR Part 39, Airworthiness Directives 14 CFR § 91.417, Maintenance records FAA Airworthiness Directives FAA AD Applicability and Compliance FAA Dynamic Regulatory System Next Week Plane & Pilot - Left-Turning Tendencies What are the four left-turning tendencies of an aircraft? Four aerodynamic and mechanical effects can make a propeller-driven airplane yaw or roll left, especially when power is high and airspeed is low. Next week, we will separate those effects and connect each one to what the pilot sees and corrects during takeoff and climb. How do you avoid reverse sensing when tracking a VOR? How do you correct for wind drift? Keep the Course and Indication Together A VOR station defines 360 magnetic lines called radials, and every radial extends from the station. The 180° radial, for example, extends south. If you are on that radial and want to fly north to the station, your inbound course is the reciprocal, 360°. For the outbound trip south, your course is 180°. The omnibearing selector (“OBS Knob”) sets the course you want to fly. The course deviation indicator, or CDI, shows whether that selected course lies left or right of the airplane, while the TO/FROM indication identifies the course's relationship to the station. A centered needle alone does not prove that the receiver is set correctly; the CDI can center on either direction of the same course line. Despite their seeming complexity, CDIs are simple - select the course you intend to fly, then confirm TO for an inbound course or FROM for an outbound course. In the example, set 360° and confirm TO when flying north to the station; set 180° and confirm FROM when flying south away from it. If the course is set for the opposite direction, the CDI will command corrections in the wrong direction. Tip: Keep the head of the selected VOR course and the airplane's nose generally pointed in the same direction, then verify the TO/FROM indication before trusting the needle. For wind drift, use the needle as course information rather than a steering command. If it moves off center, turn toward the selected course with a modest intercept angle. As the needle returns, reduce the intercept and establish a small wind-correction angle into the wind. Adjust that crab a little at a time. Chasing every needle movement tends to produce overshoots and S-turns instead of a stable track. Apply It Near Green Castle The current Chicago Sectional provides a useful local picture. Green Castle Airport (IA24) lies southeast of the Cedar Rapids VOR/DME (CID), close to the facility's 156° radial. A pilot using that line toward CID would select the reciprocal course, approximately 336°, and confirm TO. Flying southeast away from CID would call for approximately 156° with FROM. This local example connects three ideas that are easy to blur together: a radial names the line from the station, a course names the direction you intend to fly along that line, and heading is where the nose points. The related GCAC refreshers on VOR, DME, TACAN, and VORTAC and course, heading, and track explain those building blocks. Before trying it in the airplane, use the VOR Trainer on GCAC's E-Teaching Tools page. Change the selected course and aircraft heading, then predict the CDI and TO/FROM indications before looking at the result. In flight, identify the station, verify a usable signal, and make smooth corrections. Near station passage, allow for rapid or unreliable indication changes rather than chasing the needle. FAA Sources and References Pilot's Handbook of Aeronautical Knowledge, FAA-H-8083-25C, Chapter 16, pp. 16-24 to 16-26 and Figure 16-32 Aeronautical Information Manual, Chapter 1, Section 1, paragraph 1-1-3 FAA VFR Raster Charts, Chicago Sectional chart Next Week Regulations - Airworthiness Directives What are airworthiness directives (ADs), and when are they issued? A maintenance record can look complete and still leave an essential compliance question unanswered. Next week, we'll examine why the FAA issues airworthiness directives and what a pilot should confirm before flight. What is the recommended entry into a non-towered airport pattern when approaching from the opposite side of the pattern? The FAA's preferred, commonly called "teardrop" entry from the opposite, or upwind side of a left-hand pattern is to cross midfield at least 500 feet above traffic pattern altitude, fly clear of the pattern by approximately 2 miles, descend to pattern altitude, and turn right to join the 45-degree entry to midfield downwind. That extra-altitude crossing lets you observe the airport and traffic without descending through the pattern. For a normal 1,000-foot AGL piston-airplane pattern, the crossing would normally be at least 1,500 feet AGL. The Airplane Flying Handbook recommends remaining at 2,000 feet AGL when large or turbine aircraft operate at the airport so you do not conflict with their higher pattern. The alternate, commonly called a direct entry, crosses midfield at pattern altitude, yields to traffic on the preferred 45 and downwind, and then turns directly onto downwind. The FAA calls it the alternate midfield entry and says it should not be used when the pattern is busy. The preferred route gives you an easier escape: If traffic prevents entry, continue away from downwind and try again. These are FAA recommendations, not a regulation prescribing one entry path. Regulations govern traffic-pattern flow and right-of-way, while the entry guidance helps pilots arrive predictably and reduce collision risk. Mirroring the Entry at Green Castle At Green Castle Airport (IA24), field elevation is 756 feet MSL and the Club-published traffic pattern altitude is 1,756 feet MSL. That makes the normal preferred midfield crossing at least 2,256 feet MSL. Note: The KCID Class C shelf begins at 2,100 feet MSL. To fly an overhead midfield pattern entry at IA24, you will need to be in contact with Cedar Rapids Approach. Before flight, review the pattern-altitude refresher and verify current charts, airport information, and NOTAMs. The FAA figure assumes a left-hand pattern. Green Castle uses left traffic for Runway 33 and right traffic for Runway 15, so the geometry must be mirrored for Runway 15. The crossing altitude and outside-the-pattern descent remain the same, but the final turn onto the 45 must place you on the correct side of the runway. The Club's traffic-pattern diagrams show both runway patterns, and the related pattern-direction refresher explains how to confirm left versus right traffic. A good arrival briefing therefore answers four questions before you reach the airport: Which runway? Which pattern direction? What pattern altitude? Where will you descend and join the 45? Keep listening and looking throughout the maneuver; a quiet CTAF does not mean the pattern is empty. FAA Sources and References AC 90-66C, Non-Towered Airport Flight Operations, paragraphs 8.2.1 and 11.3; Appendix A, p. A-5 Airplane Flying Handbook, FAA-H-8083-3C, Chapter 8, pp. 8-4 to 8-5, Figure 8-3 Aeronautical Information Manual, paragraph 4-3-3 Next Week Airspace & Navigation - Tracking a VOR How do you avoid reverse sensing when tracking a VOR? How do you correct for wind drift? The CDI can give useful guidance only when the selected course and indication agree with the flight you intend. Next week, we'll connect that setup to small, disciplined wind corrections that keep the airplane tracking smoothly. |
AuthorGCAC flight instructors bring wisdom from a multitude of aviation backgrounds totaling tens of thousands of flight hours. Categories
All
Archives
November 2026
|
RSS Feed